EnGenius EAP9550 Access Point Firmware 1.3.2 Download

Posted at November 5, 2024 by PCI-DB Team

EnGenius EAP9550 Access Point Firmware 1.3.2 Description

Wireless N 300Mbps Access Point / Universal Repeater with Smoke Detector Design & 802.3af PoE

HARDWARE SPECIFICATIONS:
MCU: RT3052
Memory: 32MB SDRAM
Flash: 4MB
Physical Interface:
LAN One 10/100 Fast Ethernet RJ-45
Reset Button
Power Jack
LEDs Status:
Power (Status)
LAN (10/100Mbps)
WLAN (Wireless Connection)
Power Requirements:
Power Supply: 90 to 240VDC ± 10%, 50/60Hz (Depends on different countries)
Active Ethernet: (Power-over-Ethernet, IEEE 802.3af) 48VDC/0.375A
Device: 12V/1A
Regulation Certifications: FCC Part 15, UL, CE

RF SPECIFICATIONS:
Frequency Band: 2.400~2.484GHz
Media Access Protocol: Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA)
Modulation Technology: OFDM: BPSK, QPSK, 16-QAM, 64-QAM, DBPSK, DQPSK, CCK
Operating Channels: 11 for North America, 14 for Japan, 13 for Europe
Receive Sensitivity (Typical):
IEEE 802.11n
MCS8 @ -90dBm
MCS15 @ -70dBm
IEEE 802.11g
6Mbps @ -92dBm
54Mbps @ -72dBm
IEEE 802.11b
1Mbps @ -93dBm
11Mbps @ -89dBm
Available Transmit Power:
IEEE 802.11n/g
18dBm @ 6~9Mbps / MCS9
16dBm @ 12~18Mbps / MCS11
14dBm @ 24~36Mbps / MCS13
13dBm @ 48~54Mbps / MCS15
IEEE 802.11b
17.5dBm @ 1~11Mbps
Antenna: Directional Embedded Antenna x2; Peak Gain 4dBi
Standard: IEEE 802.11n & 802.11b/g
Frequency Range: 2.4 to 2.49GHz
V.S.W.R.: 2:1
Feed Impedance: 50Ohm
Power Handling: 30dBm
Interface: Two sets of soldering pads for 50ohm, 1.13mm diameter, micor coax cable
Antenna Dimensions: 100mm x 50mm
Weight: 0.03oz (9g)

SOFTWARE FEATURES:
Topology: Infrastructure
Operation Mode: Access Point / Universal Repeater / WDS
LAN: DHCP Server / DHCP Client
Wireless:
Wireless Mode 802.11b / 802.11g / 802.11n
Signal Strength
Bandwidth Selection 40/20MHz
Transmission Rate
802.11b/g: 54, 48, 36, 24, 18, 12, 11, 9, 6, 5.5, 2, 1 in Mbps
802.11n: See Below Chart
Guard Interval 800ns
Guard Interval 400ns

Security:
WEP Encryption 64/128bits
WPA Personal (WPA-PSK using TKIP or AES)
WPA Enterprise (WPA-EAP using TKIP)
802.1x Authenticator
Hide SSID in Beacons
Multiple SSID with 802.1q VLAN Tagging (up to 4 SSID)(Access Point mode)
MAC Filter (Access Point mode)
WLAN L2 Isolation (Access Point mode)
Wireless STA (Client) Connected List
QoS: WMM

MANAGEMENT:
Configuration: Web-Based Configuration (HTTP) / Telnet
Firmware Upgrade: Upgrade Firmware via Web Browser; Keep Latest Setting When Firmware Update
Administrator Setting: Administrator Password Change
Reset Setting: Reboot (Press 1 second) / Reset to Factory Default (Press 10 seconds)
System Monitoring: Status, Statistics and Event Log
SNMP: V1, V2c
MIB: MIB I, MIB II (RFC1213), and Private MIB
Traffic Measurement: Per Interface
Bandwidth Measurement: IP Range & Bandwidth Management
Backup & Restore: Settings Through Web

ENVIRONMENT & PHYSICAL:
Temperature Range: Operation 0°C to 45°C (32°F to 113°F) / Storage -20°C to 70°C (-4°F to 158°F)
Humidity (Non-condensing): 0% ~ 95% Typical
Dimensions: Diameter: 120mm (4.72”) x Height: 50mm (2.17”)
Weight: 0.62lb. (280g)

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related EnGenius Drivers