NETGEAR WNR834Bv2 Wireless Router Firmware 1.0.32 NA Download

Posted at November 2, 2024 by PCI-DB Team

NETGEAR WNR834Bv2 Wireless Router Firmware 1.0.32 NA Description

Bug Fixes:

- Fixed PPPoE client disconnect issue (for the cases of: Out of order PADO / PADR sequence, “passive” option, drop-line under heavy traffic, server doesn’t response echo-request etc).
- Fixed router hang issue under stress PPLive & Foxy traffic.
- Fixed the DHCP client ARP conflict and cannot get IP assignment issue.
- Fixed Vista wireless client incorrectly detect router as WPA-enterprise security if WPS function is enabled. (Note: This bug occurs on v1.0.30 only)
- Fixed issues - Web UI sometimes hang issue.
- Fixed the Router Status page sometimes show SSID incorrectly.
- NAT bug fix: PPTP port forwarding issue
- Revised default PPTP MTU to 1436.
- Fixed the bug if received error in PADO / PADS messages from server, it will not auto reconnect even if dial on demand if on.
- NAT bug fix: Same source PC to any other WAN side should reuse the same source port.
- NAT bug fix: Different source protocol to another WAN side should reuse the same source port.

Known Issues

- If you configure the router in WEP & WPA-PSK type for 130/270Mbps mode, the throughput will be low (around 40 Mbps.) Its recommend to use WPA2-PSK or none security mode to achieve the optimized performance.
- Operating under WDS mode with WG602v3 and WG302 might get low throughput.
- In heavy/noisy wireless environment, the 270Mbps link mode might drop the link rate to low speed quickly.
- NETGEAR ProSafe VPN client from LAN cannot passthrough the router to connect to a FVS114 VPN server.

Firmware Installation:

Write down all the settings which you changed from the default values, since you may need to re-enter them manually.

- Download the firmware and save it to a convenient place such as your desktop. Unzip if needed.
- Log in to the router using a Web browser.
- Click ADVANCED tab Administration Firmware Upgrade.
- Click Browse and find the file you just downloaded.
- Click Upload. Do not interrupt the upgrade while the router does this step.

Note:

To avoid wireless disconnect issue during the firmware download process, NETGEAR recommends that firmware upgrade be performed on a computer with wired connection.

Important Note:

- The upgrade process is completed when the on screen progress bar completes. If power LED light turns amber and blinking, power cycle the router to complete the upgrade.
- If the upgrade progress bar on web GUI doesn’t display correctly during firmware upgrade, you can still check the status using Power LED. The Power LED should be blinking (amber) during firmware upgrade. After firmware upgrade is done and boots up the system, it changes to steady amber color.
- Please DO NOT power off or reboot the device during firmware upgrade, otherwise, it may result to a corrupt firmware and cause the device not to work.

About Router Firmware:

Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn’t either newer or matching this release.

Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.

In theory, these steps shouldn’t be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don’t always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.

If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.

If you’re looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don’t power off the router or use its buttons during the installation, if you wish avoid any malfunctions.

If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don’t miss the update that will improve your device. 

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related NETGEAR Drivers