NETGEAR GS724Tv4 Switch Firmware 6.3.1.4 Download

Posted at December 22, 2024 by PCI-DB Team

Install Driver Automatically

Device Name	NETGEAR GS724Tv4 Switch Firmware 6.3.1.4
Category	Router Switch Access Point
Manufacturer	NETGEAR
File Size	14.3 MB
Supported OS	OS Independent

NETGEAR GS724Tv4 Switch Firmware 6.3.1.4 Description

GS716Tv3, GS724Tv4 and GS748Tv5 are Netgear’s hardware refreshed smart switches based on previous old version GS716Tv2/GS724Tv3/GS748Tv4. This maintenance release is to support EAV (Ethernet Audio Video) feature on GS716Tv3/GS724Tv4 and GS748Tv5. Moreover, some software issues were fixed in this release. The release notes contains the fixed issues and known issues.

GS716Tv3, GS724Tv4 and GS748Tv5 support the latest Smart Control Center, please use SCC version 1.1.3.2 for switch discovery, basic configuration and FW upgrades.
Note also that the fw 6.3.1.x can only be used for GS716Tv3/GS724Tv4/GS748Tv5, and can NOT be used on previous switch GS716Tv2/GS724Tv3/GS748Tv4.

This release notes contains features and known issues for GS716Tv3/GS724Tv4/GS748Tv5 firmware.

GS716Tv3, GS724Tv4 and GS748Tv5 support the latest Smart Control Center, please use SCC version 1.1.3.2 for switch discovery, basic configuration and FW upgrades.

Note also that the fw 6.3.0.x can only be used for GS716Tv3/GS724Tv4/GS748Tv5, and can NOT be used on previous switch GS716Tv2/GS724Tv3/GS748Tv4.

Fixed issues

- Changed Priority of existed access-control-rule failed
- File Type 'undefined' is listed in TFTP download page when HTTPS is enabled.
- EAV feature is not fully ready for GS748Tv5.
- Rpoter can't access by GUI after enable DNS and SNTP on DUT and running about 30H
- Router abnormally reboot when enable IGMP snooping on all interfaces and click "IGMP Snooping Configuration" page

Known issues

- Warning messages pop up when enable the https admin status
- [Workaround]: Refresh the GUI page.
- Cable test result sometimes shows much longer value
- [Workaround]: Redo the cable test on the same port.

Notes and limitations

- It is NOT supported for configuration migration from old devices GS716Tv2/GS724Tv3/GS748Tv4 to new devices GS716Tv3/GS724Tv4/GS748Tv5.
- The boot time for GS716Tv3/GS724Tv4/GS748Tv5 is about 40 seconds longer than GS716Tv2/GS724Tv3/GS748Tv4.
- During the boot time (about 2 minutes), all LED lights on for GS716Tv3 and GS724Tv4. This is working as HW design.

About Switch Firmware

Given the large variety of models and different methods for upgrading the switch, if you wish to apply this package, we recommend that you read and understand the installation steps before you install a new firmware, even if you are a power user.

Usually the update procedure isn’t much of a hassle as manufacturers try to make it as simple as possible; however, there are cases that are exceptions to this rule. First off, go to the system information page of the switch to check that the currently installed version isn’t either newer or matching this release.

Applying a new firmware can decrease the security vulnerabilities, enhance overall performance and compatibility, improve various power management functions, resolve different errors, and add support for newly developed technologies and protocols.

It is recommended that you perform this step in a steady power environment such as the one ensured by a UPS unit, and that you don’t interrupt the upgrade in any way, because this might cause the switch to malfunction.

That being said, click the download button, get and apply the new version, and check back with our website constantly to stay up to speed with the latest releases. 

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related NETGEAR Drivers