Gigabyte GA-6PXSVT (rev. 1.0) aSpeed Graphics Driver 0.95.01 Download

Posted at December 22, 2024 by PCI-DB Team

Gigabyte GA-6PXSVT (rev. 1.0) aSpeed Graphics Driver 0.95.01 Description

Specifications:

Form Factor:
- ATX
- 305W x 244D (mm)

CPU:

- Intel Xeon E5-2600 V2 processors
- Intel Xeon E5-1600 V2 processors
- Intel Xeon E5-2600 processors
- Intel Xeon E5-1600 processors
- Intel 2nd & 3rd Gen. Core i7 processors

Socket:

- 1 x LGA 2011
- Mounting pitch: narrow ILM (56x94mm)
- Recommended cooling device dimension: 70x106mm
- Max. length of M4 screw threads: 3.7mm
- Screws longer than 3.7mm might damage the motherboard

Chipset:

- Intel C602

Memory:

- 8 x DIMM slots
- Quad channel memory architecture
- ECC & non-ECC UDIMM/RDIMM modules supported
- Single and dual rank UDIMM modules up to 8GB supported
- Single, dual and quad rank RDIMM modules up to 32GB supported
- 1.35V modules: 1066/1333/(1600) MHz
- 1.5V modules: 1066/1333/1600/(1866) MHz

LAN:

- 2 x GbE LAN ports (Intel 82574L)
- 1 x 10GbE SFP+ LAN port (Intel 82599EN)

Video:

- Integrated in Aspeed AST2400
- 2D Video Graphic Adapter with PCIe bus interface
- 128MB memory
- 1920x1200@60Hz 32bpp

SATA:

- 2 x SATA III 6Gb/s supporting SATA DOM
- 8 x SATA III 6Gb/s from Marvell 88SE9230 controller
- 4 x SATA II 3Gb/s

RAID:

- Intel SATA RAID 0/1/10/5
- Marvell SATA RAID 0/1/10

Expansion Slot:

- 2 x PCIe x16 (Gen3 x16 bus) slots or (via PCIe switch)
- 1 x PCIe x16 (Gen3 x16 bus) slot
- 2 x PCIe x16 (Gen3 x8 bus) slots

Internal I/O:

- 1 x 24-pin ATX main power connector
- 1 x 8-pin ATX 12V power connector
- 1 x PMBus connector
- 4 x System fan headers
- 1 x CPU fan header
- 1 x SATA SGPIO header
- 1 x SATA port 0 DOM support jumper
- 1 x SATA port 1 DOM support jumper
- 1 x BIOS upgrade ROM
- 10 x SATA III 6Gb/s ports
- 4 x SATA II 3Gb/s ports
- 1 x CMOS battery socket
- 1 x Chassis intrusion jumper
- 1 x Clear CMOS jumper
- 1 x Clear password jumper
- 1 x Front panel header
- 1 x USB 2.0 Type A connector
- 1 x Backplane board header
- 1 x BIOS recovery jumper
- 1 x BIOS write protect jumper
- 1 x USB 3.0 header
- 1 x USB 2.0 header
- 1 x Serial header
- 1 x BMC upgrade ROM
- 1 x TPM header
- 1 x LAN3 active LED
- 1 x BMC readiness LED
- 1 x ME Recovery jumper
- 1 x PCIE1 and PCIE2 bandwidth switch jumper
- 1 x PMBus select jumper
- 1 x Force to stop FRB3 timer jumper
- 1 x S3 power on select jumper

Rear I/O:

- 4 x USB 3.0
- 2 x USB 2.0
- 1 x PS/2
- 1 x Serial
- 1 x VGA
- 1 x SFP+
- 2 x RJ45
- 1 x ID button with LED

TPM:

- 1 x TPM header

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related ASPEED Drivers