NETGEAR D6400 Router Firmware 1.0.0.34 Download

Posted at December 19, 2024 by PCI-DB Team

NETGEAR D6400 Router Firmware 1.0.0.34 Description

New Features & Enhancements:

- Wireless driver update for CE 2.4GHz power issue
- Removed IPTV / DHCP option 60 in Setup Wizard while it’s set to UK/Sky and VDSL mode
- Added ISP option list in Setup Wizard in ETH-WAN DHCP mode
- Wireless AP mode picture update (for D6400)
- DSL quick scan table updated
- Added DFS channels support in Europe and Australia
- Removed the Setup Wizard log
- Added IPTV option in Setup Wizard for known ISP, It will bridge LAN4 and VDSL VLAN 30 interface
- Disabled VLAN option in Setup Wizard page (user cannot change it in Setup Wizard)
- Wording change in Internet Setup page / Router Status page: WAN1 to Internet, WAN2 to IPTV
- Added “WAN2 bridge to LAN4” option in Internet Setup page
- Added XAgent (Remote Genie) support
- Updated DSL PHY driver and enable SRA and G.INP support
- Added NA sku support
- Internal wireless parameter change : watchdog from 60000 msec to 3000 msec for Home IOT issues

Bug Fixes:

- Fixed the issue with Wireless Setup page on Chrome browser
- Fixed the issue where OpenVPN information incorrect in non-English version
- Fixed the issue where upgrading the FW through internet crashes the router
- Fixed some issues happened in WPA/WPA2 Enterprise Test
- Fixed the issue where Asia 5GHz GUI channel can't set 36,40
- Fixed the issue where router statistics show incorrect LAN interface uptime
- Fixed the issue where BT WAN detection fail at ETH mode while IPTV is enabled
- Fixed the issue where LAN PC doesn't get IP address from WAN when enable IPTV from VLAN / Bridge Setup page
- Fixed the SoapAPI: Many API run failed during SOAP testing
- Fixed the issue where browse button is not translated into Chinese on Setup Wizard restore router settings page
- Fixed the issue where there is no ReadySHARE Vault option in USB function
- Fixed the issue where Wireless client can't connect to router when its security mode is WPA/WPA2 Enterprise with EAP-TLS authentication
- Fixed SOAP vulnerability (Need password requirement for SOAP API)

Known Issues:

- PnP-X driveris not ready

Note:

- To avoid wireless disconnect issue during the firmware download process, NETGEAR recommends that firmware upgrade be performed on a computer with wired connection.
- Write down all the settings which you changed from the default values, since you may need to re-enter them manually.

To Install:

- Download and extract the new firmware to a convenient place such as your desktop.
- Log in to the router using a Web browser.
- Click ADVANCED tab > Administration > Firmware Upgrade.
- Click Browse and find the file you just downloaded.
- Click Upload. Do not interrupt the upgrade while the router does this step.

Important Note:

- The upgrade process is completed when the on screen progress bar completes. If power LED light turns amber and blinking, power cycle the router to complete the upgrade.
- If the upgrade progress bar on web GUI doesn’t display correctly during firmware upgrade, you can still check the status using Power LED. The Power LED should be blinking (amber) during firmware upgrade. After firmware upgrade is done and boots up the system, it changes to steady amber color.
- Please DO NOT power off or reboot the device during firmware upgrade, otherwise, it may result to a corrupt firmware and cause the device not to work.

About Router Firmware:

Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn’t either newer or matching this release.

Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.

In theory, these steps shouldn’t be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don’t always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.

If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.

If you’re looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don’t power off the router or use its buttons during the installation, if you wish avoid any malfunctions.

If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don’t miss the update that will improve your device.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related NETGEAR Drivers