NETGEAR FS728TPv2 Switch Firmware 5.0.2.45 Download

Posted at November 18, 2024 by PCI-DB Team

Install Driver Automatically

Device Name	NETGEAR FS728TPv2 Switch Firmware 5.0.2.45
Category	Router Switch Access Point
Manufacturer	NETGEAR
File Size	3.9 MB
Supported OS	OS Independent

NETGEAR FS728TPv2 Switch Firmware 5.0.2.45 Description

Bug Fixes:

- Fixed the issue where the connection is lost for few seconds every 2 to 3 weeks with some IP phones.
- Fixed the issue where the device view fails to come up after updating to Java JRE 7u51 (1.7.0_51-b13) or newer versions on the host computer.
- Fixed the issue where the switch might reboot if using SNMP for monitoring over some period of time.
- Improved device ICMP echo response time as it can be erratic when pinged.
- Fixed the issue where the system freezes when downloading HTTPS/SSL certificate file (server.pem) to the switch.
- Addresses the following security vulnerability issues published on CVE web site: CVE-2013-4775
- Fixed the issue where the EAP packet with unicast destination address is blocked when “EAPOL Flooding mode” is enabled while “802.1X admin mode” is disabled.
- Fixed the port security issue with static MAC.When a static MAC address is specified and the “Max Allowed Dynamically Learned MAC” is set to 0 for a port, this MAC address can still be learned by other ports.As a result, device with this MAC can work with other ports with “Max Allowed Dynamically Learned MAC” not set to 0, but not with the port with static MAC configured.
- Fixed the issue where the FAN failure LED does not get turned off after the FANs start to work normally again.

Known Issues:

- While the link is up, port cannot be removed from a VLAN if it is also member of a LAG.
- Workaround: Remove the link or remove the port from the LAG first.
- After setting the maximum number of allowed static locked MAC address to zero (under Security > Traffic Control > Port Security > Interface Configuration), no static MAC address can be added even when port security is disabled.
- Workaround: Change back the "Max Allowed Statically Locked MAC" from 0 to 20.
- Can’t remove a policy entry completely in the table under QoS > Diffserv > Advanced > Policy Configuration the first time.
- Workaround: Need to select the same entry and click DELETE again.
- In some cases, the device may fail to boot after pressing the factory default button on the front panel
- Workaround: Please reboot the device manually.

Upgrade Procedure:
1) Save the current configuration data. Normally, the firmware will preserve the original configuration in the switch. However, because this is a major firmware upgrade, you may want to save a copy of current running configuration, just in case something goes wrong during the upgrade. To do so, go to "Maintenance -> Upload" page, and select Text Configuration option and click the Apply button to save the configuration file.
2) Download the new firmware from the NETGEAR product support page and store it in a PC, and remember its location in the PC’s file system.
3) There are two ways to download the new firmware from PC to the switch:
- One is using TFTP which requires a TFTP server be installed on the PC where the firmware is stored from step #2. If you preferred to use TFTP method, or you're using telnet session to perform firmware upgrade, continue to step 5.
- The second method is to use web browser for downloading which requires of no TFTP server. Continue to the next step to use HTTP file download.
4) To use HTTP method, go to the following web GUI page (Maintenance -> Download -> HTTP File Download), select the location of the new firmware via the Choose File button, and click the Apply button to start firmware upgrade. The upgrade will take about 12 minutes. Do not power cycle the switch before the process is complete.
- After the Apply button is clicked, the file transfer will start, and followed by writing the new image to the Flash memory. Do not power cycle or reboot the switch before the process is complete, and the success message will show up as below.
- After the successful completion the upgrade, proceed to step #8 to restart the switch.
5) To use the TFTP method, start a TFTP server on the PC where the new images are stored. If you do not have a TFTP server, we recommend using free tools such as PumpKIN or TFTPD32.
6) You can use either web interface or CLI interface to perform upgrade using TFTP. To use web interface, go to "Maintenance -> Download -> File Download," select Transfer Mode as TFTP, complete the text fields on the page and hit Apply to start. To use CLI, either telnet into the switch or use console port and follow these steps below.
7) On the switch console, type the following command:
a. # copy tftp://<tftp server IP address>/<image name> system:image
b. It will ask for confirm with input data displayed. Hit enter if all parameters look correct.
c. The download should take a minute or two. After that, the code will be checked for possible corruption, if not, it will report firmware successfully upgraded.
d. Reboot the switch by typing "reload" command or power cycle the switch.
8) To use GUI to restart the switch, go to web page "Maintenance -> Reset" page, Device Reboot table.
- Make sure that "All" is selected in "Reboot Unit No" drop down menu box. If it is shown with some other value like "1", then only unit 1 in the stack will be rebooted, and this may result in stack failure after the stack is rebooted. You may select "Save prior to reboot" option if you feel there are changes that may not have being saved. Click the Apply button to start the reboot process.
9) After the switch is restarted, type the following CLI command to verify the version is correct.
a. # show hardware
b. Or, go to GUI System main page (System -> Management -> System Information, under Device Status) to confirm the switch firmware is the one downloaded.
10) Verify the switch running configuration by issuing "show running-config" command. The output should match the configuration file saved on step #1. If they are not, please call NETGEAR customer support on discrepancy and manually re-apply the missing configuration commands back to the switch.
11) You can now make additional configuration changes for other applications, and be sure to use "save" command to save the configuration after you're done.

About Switch Firmware:

Given the large variety of models and different methods for upgrading the switch, if you wish to apply this package, we recommend that you read and understand the installation steps before you install a new firmware, even if you are a power user.

Usually the update procedure isn’t much of a hassle as manufacturers try to make it as simple as possible; however, there are cases that are exceptions to this rule. First off, go to the system information page of the switch to check that the currently installed version isn’t either newer or matching this release.

Applying a new firmware can decrease the security vulnerabilities, enhance overall performance and compatibility, improve various power management functions, resolve different errors, and add support for newly developed technologies and protocols.

It is recommended that you perform this step in a steady power environment such as the one ensured by a UPS unit, and that you don’t interrupt the upgrade in any way, because this might cause the switch to malfunction.

That being said, click the download button, get and apply the new version, and check back with our website constantly to stay up to speed with the latest releases. 

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related NETGEAR Drivers