Cisco RV320 Router Firmware 1.3.1.12 Download

Posted at November 21, 2024 by PCI-DB Team

Cisco RV320 Router Firmware 1.3.1.12 Description

New Features:

- FlexVPN (hub and spoke)
- OpenVPN

Resolved Issues:

- Bitmask of Circuit ID hex type doesn’t work (CSCus78529)
- Memory leak for mdnsd process (CSCuw02356)
- DHCP Range overlap error seen incorrectly (CSCut07184)
- Change the maximum number of IP&MAC binding entries to 80 (CSCus81690)
- IP & MAC Binding breaks DHCP server functionality (CSCuv64052)
- Remote management access stops working intermittently (CSCuu42921)
- SIP ALG not modifying all fields (CSCuv05601)
- IPv6 continuous pings can cause reboot (CSCuu90949)
- Only support lowercase letters in CLI command (CSCus60459)
- Error creating Port Forwarding for VLAN that is subnetted (CSCur83582)
- DHCP Offer does not respond Option 55 with item (0) padding (CSCuu62007)
- Bandwidth Management Rules limit sum of Max Rates to ISP Max BW (CSCut04618)
- RV320: WAN port goes inactive intermittently (CSCuu10991)
- Router blocks inbound SIP Invite intermittently (CSCuu00900)
- RV320: Incorrect error for USB modem when NSD is disabled on WAN (CSCut08978)
- IP & MAC Binding breaks DHCP server functionality (CSCuv64052)
- RV320: Huawei E3272lte 4G modem (CSCur08152)
- RV325: DWM-157 3G/4G modem is not available. ISP: Telenor, Norway
- RV320: Recognizes DWM-157, but SIM card is not recognized. ISP: Three UK
- RV320: Recognizes D-Link DMWM-157, no internet. Telenor, Hungary
- RV325: /28 Private IP Address should be under wrong subnet.

Caveats Acknowledged in Release 1.3.1.12:

 
- RV320: Inter VLAN routing not working with 1:1 NAT (CSCuv74771)
- iOS/MacOS built-in vpnclient can't connect with split-tunnel mode (CSCuw30159)
- DDNS username won't allow more than 25 characters (CSCuv78522)
- Allow Policies showing in logs when not enabled (CSCuw79932)
- RV320: DDNS account longer than 11/12 symbols is not accepted (CSCux99100)

Installation Procedure:

- Save the downloadable package.
- Log into the router’s web user interface.
- Navigate to the firmware upgrade section of your wireless unit.
- Select the present firmware and configure your router to install this file.
- Wait as the device carries out this process.
- Reboot the unit if required.

About Router Firmware:

Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn’t either newer or matching this release.

Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.

In theory, these steps shouldn’t be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don’t always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.

If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.

If you’re looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don’t power off the router or use its buttons during the installation, if you wish avoid any malfunctions.

If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don’t miss the update that will improve your device. 

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Cisco Drivers